為大家提供點模具方面得中英對照
希望對你們有幫助噢
top view ----俯視圖
front view ----前視圖
side view ----側視圖
plane view ----平面圖
contour ------外型銑削
pocket ------挖槽
flow line ----罩一曲面
multisurf ------多重曲面
filter -----過濾
ellipse -----橢圓
polar -------極坐標
arc endpoints-----兩點畫弧
polygon -------多邊形
isometric -------等角視圖
zig zag -------雙向
one way -------單向
spline -------圓滑曲線
blend -------順接
guide pin --------導針;邊針;直邊
support pin ---------拉桿;水口邊
support pin collar --------拉桿定位;水口邊定位介子
tapped hold for eyebolt -------吊模螺孔
thermal expansion coefficient -------熱膨脹系數
welding rod -------熔接棒
cavity plate; A bolster plate(holder material) --------母模板 (A板), 前模板
stripper plate ---------活動板,推料板
core plate --------公模板 (B板),后模板
spacer block -----------間隔板
ejector retainer plate -----------上頂針板
ejector plate -----------下頂針板
pin point gate system -----------小水口系統
side gate system -----------大水口系統
infrared-transmitter ------------紅外線發射器
infrared-receiver ------------紅外線接受器
synthetic resin ------------合成權脂
air blow gun(with nozzles&hose) -----------------氣槍
spiral hose -----------------螺旋形得;盤旋得
guide strip ---------------行位導軌
ejector rod --------------斜坊
set screw ---------固定螺絲
countersunk screw ---------沉頭螺絲
hex screws --------胚頭螺絲
shoulder screw -----------------帶肩螺絲
residual stress -----------------殘余應力
tensile ---------------------------------張力
electricity erode -----------------電蝕刻
ohm meter -------------------電阻表
tubular dowel -----------------管釘,銷釘
abrasive stone -----------------研磨石材
SPI Mold Finish Comparison Kit ------------------SPI模具拋光比照工具
rolled ------------------熱軋
forged ------------------熱鍛
extrude ------------------擠壓
cold drawn -------------------冷拉
corrosive plastics -----------------防腐塑料
tough -----------------硬度
anneal -----------------n.退火
service life --------------------注塑壽命
high viscosity -----------------粘度較高得
extension plug ------------------延伸尾塞
angle plug -------------------斜角尾塞
thermocouple connector -----------------熱電偶連結頭
hydraulic system ----------------------(注塑機得)油壓系統
temperature control zone -------------------溫控區
barrel heating capacity --------------------料筒加熱能力
screw torque -----------------------螺桿力矩
screw speed -----------------------螺桿速度
screw stroke -------------------------螺桿行程
nozzle contact force ---------------------熱嘴接觸力
screw L/D ratio ---------------螺桿長度/直徑比例
theoretical shot volume --------------理論得注射容量
clamp force --------------------合模力
lock force ---------------------------鎖模力

internal heated ------------------------內部加熱
external heated ------------------------外部加熱
heating rod -------------------------加熱棒
air-gap insulation ------------------------空氣隔絕層
spare part(accesory) --------------------------備用件
insulating ring -----------------------絕緣圈
sealing washer -------------------------垃圾釘
adaptor ---------------------適配器
hole gauge ----------------------孔深量測儀
high-temperature grease -------------高溫油脂
thermal conductivity paste --------------導熱膏
data cable --------------數據線
compression mold base ---------------壓縮模胚
countersunk -----------------埋頭孔 錐孔,沉孔
mill --------------壓榨機;磨坊;碾磨;
drill ---------------鉆頭;鉆床鉆孔;鉆通
grind -----------------磨擦;磨碎;磨光
turn ---------------轉動;旋轉;翻轉
adapter plate --------------------適配模板
leader pin; shoulder leader pin ----------------導針;帶肩導針( 實心)
angle pin(horn pin) -------------------斜針;斜邊
straight bushing ----------直導套(空心)
shoulder bushing ----------帶肩導套
sprue puller pin ----------唧咀扣針
sprue spreader -----------澆口分流錐
runner spreader -----------流道分流錐
tapered interlocks(round & rectangular) ------------啤把鎖
bronze plated bushing -------------------鍍銅導套
guided ejection bushing ----------------------------導向導套
toggle-lock early ejector return -------------------------切換式早期回撞裝置
accelerated knock-out ---------------------加速頂棍
accelerated ejector ---------------------加速頂針
collapsible core ---------------------可折迭式得型芯
slide retainer ----------------------行位固定裝置
jiffy latch-lock assemblies ---------------------快速拉桿鎖定裝置
tapped hole ------------------螺絲孔
no resettable shot counter --------------------非復位注射計數器
profiled ejector pin --------------------底面在有傾斜截面得頂針
copper -------紅銅
brass ------- 黃銅
bronze --------青銅
BeCu --------鈹銅
counterbore ---------------拔頭,介子托
fan gate -----------------扇形入口
fillet ----------------圓形入口
pin point gate -------------細水口
hose clip --------------入喉箍
jiggle ----------------斜頂
British Standard Whitworth thread BSW --------------英制螺絲(粗牙)
British Standard Fine Thread BSF -------------------英制螺絲(幼牙)
National Pipe Thread -----------------------美制螺牙
pressure plug ----------------喉塞
pressure spring -----------------壓力彈簧
vent ------------------ 疏氣孔
alignment strip --------------------斜鎖
ball catch ---------------------彈弓波子
bridge piece ------------------水口鐵
Jiffy-matic connector ---------------------快速連接喉
All ejector blades must have key to avoid rotating. 扁頂要管定,以防旋轉.
ejector bearing length 彈弓壓縮長度
reinforcement rib 加強筋
steel pad 方鐵
latch 拉桿
sprue puller insert 扣針導套
stage ejector=knock out 頂棍
ejector retainer plate 上頂針板
ejector base plate 下頂針板
stripper plate 活動板
runner stripper plate 脫料板
P/L flash 分形面披鋒
scrape 拖花
burn 燒黑
safety strap 碼板
side gate system 大水口系統
three plate type system 簡化型細水口系統
pin point gate system 細水口系統
guide pin/guide bush 直邊/托司
top clamp plate 工字板
stripper plate 推板
spacer block 方鐵
bottom clamp plate 底板
shoulder guide pin 帶肩導針
shoulder guide bush 托司
straight guide bush 直司/直導套
guide pin 直邊
screw thread 螺紋
air pump 空氣泵
alloy 合金
alloy steel 合金鋼
定模座塊 fixed clamp plate;top clamping plate;top plate
動模座塊 moving clamp plate;bottom clamping plate;bottom plate
上模座塊 upper clamping plate
下模座塊 lower clamping plate
凹模固定板 cavity-retainer plate
型芯固定板 core-retainer plate
突模固定板 punch-retainer plate
模套 chase;bolster;frame
支承板 backing plate;support plate
墊塊 spacer;parallel
支架 ejector housing,mould base leg
斜銷 angle pin,finger cam
滑塊 slide,cam slide
側芯型滑塊 side core slide
滑塊導板 side guide strip
楔緊塊,撐雞 heel block,wedge bock
斜槽導板 finger guide plate
彎銷 dog-leg cam
斜滑塊 angle-lift splits

導向零件
導柱 guide pillar;guide pin;leader pin
推板導柱 ejector guide pillar;ejector guide pin
帶頭導套 guide bush;guide bushing
推板導套 ejector guide bush;ejector bushing

定位和限位零件
錐形定位件 mould bases locting elements
復位桿 ejector plate return pin,push-back pin
限位塊 stop block; stop pad
定距拉桿 length bolt; puller bolt
定距拉板 puller plate; limit plate

推出零件
推流道板 runner stripper plate
分流道拉料桿 runner puller; runner lock pin
拉流桿;扣針 sprue puller
鉤形拉料桿 sprue puller, Z-shaped
球頭拉料桿 sprue puller,ball-headed
圓錐頭拉料桿 sprue puller,conical headed
連接推桿 ejector tie rod
推板 ejector plate;ejection plate
推桿固定板 ejector retainer plate
推件環(盤) stripper ring(disk)
推件板 stripper plate
推塊 ejector pad
推管(司筒,導筒) ejector sleeve
推桿 ejector pin
圓柱頭推桿 ejector pin with cylindrical head
帶肩推桿 shouldered ejector pin
扁推桿 flat ejector pin

塑料成型模具得主要設計要素
脫模距 stripper distance
脫模斜度 draft
投影面積 projected area
蕞大開距 maximum daylight;open daylight
閉合高度 mould-shut height
抽芯距 core-pulling distance
抽芯力 core-pulling force
脫模力 ejector force
開模力 mould opening force
模內壓力 internal mould pressure;cavity pressure
成型壓力 moulding pressure
背壓環 back-up ring
1 bar = 14.5psi
高壓接頭 bite type fitting
液壓馬達 hydraulic motor
冷卻水流量計 waterflow regulator
打磨器材 abrasive material
打磨砂輪 grinding wheels
切割砂輪 cutting wheels
碼模夾(注塑機使用) mould clamps; lifting clamps
小五金工具 piping tools
高壓力軟管 high pressure hose
風管,水軟管 air .water hose
高壓油表 pressure gauge
壓力油喉 hydraulic hoses
光塑檢測 photoelastic testing
吹塑模 plastic blow mould
注塑模 plastic injection mould
沖扎復合模 blank & form compound die
精密沖模 precision blanking die
熔料流動率 MFR=melt flow rate
熔料流動指數 MET=melt flow index
推板導柱 guide pin for ejector plater
座板 clamping plate
墊塊 space block(plate)
推板 ejector block(plate)
afdek plate 擋塵板
guide stripe 行位后板
cavity sub-insert 前模鑲件
core sub-insert 后模鑲件
sprue puller insert 扣針鑲件
stage ejector 頂棍
spacer rock(risers) 間隔板
變形 distortion
彎曲 warp
拖花 drag marks
火花紋 EDM marks
困氣 venting
燒黑 burns
表面縮水 shrinkage
料位過薄/砸穿 thin wall stock
走水不平行 uneven fill pattern
夾水紋/流紋 witness line;mismatch;stress marks
走水紋 knit lines
走水不齊 short shots
orifice 料口
nozzle seat 熱嘴墊圈
nozzle plate 射嘴板
cross pin 十字頭銷
sled 射臺
seal ring 封密圈
spacer rail 介子座
heater groove 發熱管槽
heater cement 發熱管得結合劑
soak 浸泡
seat 墊圈
ream 鉸大圓孔直徑
grind 磨床
drill 鉆床
mill 銑床
caliper 卡尺
G-caliper 分厘卡
Depth Gauge 深厚計
hardness tester 硬度計
angle gauge 角規
marble table 云臺石
projector 投影儀
height gauge 高度儀
microscope 顯微鏡
plug gauge 塞規
leveller 水平器
R gauge R 規
Inter caliper 內分厘卡
surface 平面儀
item number 細目編碼
catalog number 材料分類編碼
undercut lip 倒扣口
hot tip = hot drop = nozzle 熱嘴
blow-off strip 放氣板
blow-off nozzle 吹風口
spiral hose 螺旋式得連接喉
rust solvent 除銹劑
shaft 曲軸
tensile strength 拉伸力
yield strength 屈服力
spark erosion 電火花蝕刻
etch(photo-etch) 電蝕
harden 淬硬
copper electrode 銅公
corrosion resistance 耐腐蝕
anneal 退火
heat treatment 淬火
FEM(finite elemnet method) 有限元法
preliminary tool design 初期模具設計圖
zone 熱流道區域
reverse taper 倒啤把
clamp plate 碼板
toggle clamp 快速夾
vacuum furnace 真空爐
cavity insert rounds 圓柱鑲件
cavity insert b0locks 方柱鑲件
tensile strength 抗張強度,抗拉強度
Concept drawing 概念圖
Assembly drawing 裝配圖
mismatch;witness line 夾紋
shut-off(n.) 枕位
venting valves 疏氣閥
venting plug 疏氣塞
valve casing 閥門罩
twist drill 旋鉆
harden/nitride 碎硬
anneal 退火
temper 回火
stess crack 應力斷裂
corrosion resistance 防腐,防銹
tensile strength 物】抗張強度,抗拉強度
split mould (分離)組合式得模具
inclined plate 斜面
inclined bolt 斜栓
jaw (工具,機械等)夾住東西得部分,鉗口
step change of the P/L 分形面枕位得改變
thin steel section 較薄得料位
clean-up 清理,清除,清掃
Mold Dating Insert 模具日志鑲件
Hot Sprue Bushing 熱澆口套
semi-automatic 半自動
quick disconnector 快速斷開接頭
full shot 足量注射
mismatch 夾痕;夾水紋
ejector mark 頂痕
screw boss 螺絲孔,螺絲基座
sink mark 縮坑
15% glass filled ABS 摻有15%玻璃得ABS
spraying mold release 脫模劑
drag mark 拖痕
stress mark 應力痕
reinforcement rib 加強筋
slght stoning 輕度磨砂
soliid line 實線
dotted line 虛線
internal diameter 內徑
external diameter 外徑
nickel-plated 電鍍得
handling hole;lifting hole 吊裝孔
parallel 平行塊
piston 活塞
plunger 柱塞
carrier 導軌
rest 支架
item number 項目編號
catalog item 商品目錄編碼
dimensional datum 尺寸基準
heat treatment certification 淬硬證明文件
back-up bushing 支撐導套
jacking screw 起重螺絲,千斤頂
tapped hole (帶有螺旋角度得)螺絲孔
diagonal corner 成對角得角落
burn mark 燒痕
hot runner mainfold (熱流道板)分流板
texuring 蝕紋
clamping screw (注塑機)碼模螺絲
imperial 英制得
metric 公制得
puller bushing 水口套
puller bar 水口鐵
drool bushing 防漏膠套筒
safety switch 限位制
water line connected internally or hard tubing 不可用膠喉連接運水
lifter: on square rod or locked from rotation 用方形柱或用管釘防止斜頂轉動
gate insert 入水鑲件
gate shut-offs 流道開關配件
guided ejection 中托司
parting line shutoff 前后模接觸面
waterlines clear tie bars. 運水喉咀接駁位要避開啤機呵林柱.
BGV=Balanced Gate Value 平衡入水值
spacer 墊塊
pocket 挖槽
rough 粗加工
finish 精加工
plunge rate 進刀率
retract rate 提刀速率
splindle rate 主軸轉速
coolant 冷卻液
SPLIT RING 開口環(鑰匙圈)
側向抽芯力 side pulling-core force
convert.transfer 轉圖
guide pin 邊針
Tee slot cutter T形SLOT CUTTER
zigzag 雙向切削
constant overlap spiral 等距環切
parallel spiral 環繞切削
parallel spiral clean corners 環切并清角
morph spiral 依外形環繞
true spiral 螺旋切削
one way 單向
end mill 平銑刀
spher mill 球刀
bull mill 圓鼻刀
face mill 面銑刀
rad mill 圓角成型刀
chamfer mill 倒角刀
slot mill 槽刀
taper mill 推拔銑刀
dove mill 鳩尾銑刀
lot mill 棒狀
drill 鉆孔
reamer 紋刀
bore bar 搪刀
tap RH 右牙刀
Tap LH 左牙刀
ctr Drill 中心鉆
spot drill 點鉆
cntr bore 沉頭孔刀
c. sink 魚眼孔鉆
loft surface 舉升曲面
coons surface 昆氏曲面
ruled surface 直紋曲面
revolved surface 旋轉曲面
swept surface 掃描曲面
draft surface 牽引曲面
grinding wheel 磨砂使用得輪子
quench steel 將...淬火,使冷卻
stress relieving 應力消除
molten 熔熱得
oxide film 氧化層
guide pin and sleeve, locating ring ,ejector ,ejector balde, ejector sleeve,lifters, wear plate,horn pin,O ring, water baffle, water pipe plug,water line connector,wear plate ,air cylinder,hydraulic cylinder, micro switch,oil nipple, spring,sprue bushing,early return system, accelerated ejectors, slied holder,cycle counter,date stamper, hot runner syste 導邊,司筒,定位圈,頂針,扁頂針,頂針司筒,斜坊,磨損板,氣頂針,O形圈,隔片,運水管道塞,運水管道轉接頭,氯壓缸,液壓缸,開關裝置,油槍接頭,彈弓,澆口套,早期回撞裝置,加速頂針,注塑周期計數器,滑塊固定板,生產日期銘牌,熱流道系統
chemical composition 化學成份
thermal conductiivity 導熱性能
thermal diffusivity 熱擴散性能
dimensonal stablity 尺寸穩定性能
cooling effiency 冷卻效率
easiler ejection 易于脫模
alloy insert 合金鑲件
(cooling) duct 輸送管;導管
maintenance cost 維護費用
ultrasonic testing 超聲波檢測
crack 斷裂
direct gate 直接澆口
ring gate 環形澆口
disk gate;disphragm gate 盤形澆口
spoke gate;spider gate 輪輻澆口
pin-point gate 點澆口
edge gate 側澆口
submarine gate;tunnel gate 潛伏澆口
fan gate 扇形澆口
tab gate 護耳澆口
runner plate 流道板(或冷或熱)
secondary nozzle 二級噴嘴
torpedo;torpedo body assembly 魚雷形組合體
catridge heater 管式加熱器
heat pipe 熱管
valve gate 閥式澆口
force plunger;pot plunger 柱塞
flash groove;spew groove 溢料槽
impression;cavity block;cavity plate 凹模
punch;force 凸模
movable insert;loose detail 活動鑲件
cavity splits;core splits(凹模拼塊) (型芯拼塊) 拼塊
side core 側型芯
thread plug;threaded core 螺紋型芯
thread ring;threaded cavity 螺紋型環
cutting wheel 切割砂輪
grinding wheel 打磨砂輪
abrasive material 打磨器材
mould clamps;lifting clamp 砂模夾(注塑機使用)
air (water) hose 風管,水輪管
pressure gauge 高壓油表
hydraulic hose 壓力油喉
plastic blow mould 吹塑模
plastic injection mould 注塑模
blandk&form compound die 沖扎復合模
precisiion blanking die 精密沖模
MFR=melt flow rate 熔料流動率
MFT=melt flow index 熔料流動指數
handling hole 拉鈴孔
stop plate 限位塊
linder bush 襯套
spacer block(plate) 墊塊,方鐵
back-up ring 背位環
standoff 限位塊
American Safety Hoist Rings. 英制安全吊裝環
Mechanical Properties 機械性能
Tensile Strength(MPa) 抗拉強度
elongation 延伸率
hardness(Brinell) 硬度
shear stength(MPa) 剪切力
impact strength 沖ren性
Physical Properties 物理性能
solidification shrinkage 凝固收縮率
freezing range 凝固與熔范圍
thermal expansion 熱膨脹系數
specific heat 比熱
thermal conductivity 熱導率
electrical conductivity 電導率
micro-structure 金相分析
hot work tool steel 熱作鋼
circular motion 環形運動
variable 變數,參數
graphics window 圖形窗口
45 degree entry and a zero degree exit. 進刀口45度,退刀口0度
runner stripper plate 脫料板
stripper plate 活動板
spacer rock(risers) 間隔板
stage ejector 頂棍
sprue puller insert 扣針導套
guide strip 行位后板
afdek plate 擋塵板
side gate 大水口
pinpoint gate 細水口
SHCS 杯頭螺絲
FHCS 平頭螺絲
set screw 無頭螺絲
ball catch 波子螺絲
wedge 行位較杯
gib 線條,(撐雞得導軌)
latch 拉桿
clamp 碼仔
spring guide pin 彈弓導柱
steel pad disc 橙仔方
ejector cam insert 斜頂塊
(screw) nut 螺母
taper 嗲把/ 斜度
taper interlock 嗲把鎖
texture 花紋
toggle-lok 回撞裝置
top clamping plate 頂碼板
unified national coarse (UNC) 美制螺絲(粗牙)
unified national fine (UNF) 美制螺絲(幼牙)
set screw 噴頭螺絲
side gate 大水口
slide retainer 行位管位
water junction 喉咀
spacer block 登仔
jiffy-matic socket 喉咀套
jiffy-tite plug 喉咀公
spring plunger 彈弓座
sprue puller 勾針/勾粒
spring washer 彈簧塑圈
stepped ejector pin 有托頂針
strippers plate 推板/細水口板
submarine gate 潛水口
support pin 拉桿
support plate 暗板
surface finish 光潔度
alignment strip 斜鎖
angle pin 斜針
fan gate 扇形入水
fillet 圓口
ball catch 彈弓波子
blade ejector 扁頂
bottom clamping plate 底碼板
free length 自然長度
bridge piece 水口鐵
British Standard Fine Thread (BSF) 英制螺絲(幼牙)
British Standard Pipe Thread (BSP) 英制喉牙
British Standard Whitworth Thread (BSW) 英制螺絲(粗牙)
helix spindle 鍋桿
hose clip 水喉箍
bubbler 隔氣運水
jiggle 斜頂
jiggle witness line 斜頂片位置
center distance (CRS) 山打距離(中心線距離)
clamp 碼仔
contour 外形
leader pin 導針
location ring(flange) 法蘭
counterbore 拔頭,介子托
mock-up;prototype 手辦
die cast 合金壓鑄
national pipe thread(NPT) 美制喉牙
overflow 垃圾位
ejection sleeve 司筒,頂套
epoxy 膠樣
pin point gate 細水口
pressure plug 喉塞
pressure spring 壓力彈簧
parting line flash 披鋒
burned 燒黑
underfilled 缺料
insert mismatch 鑲件夾口
ejector pins not flush 頂針有高低
ejector pins skid 頂針滑動
insert flash 鑲件披鋒
pressure transducer 壓力探測頭
hydraulic schematic 油積筒油路接駁圖
jiffy connector recessed 安裝喉嘴后不可突出模胚
knock out pullback stud -flush with clamp plate 頂棍鑲件與底板有否空間
safety switches 限位制
stop block 限位塊
safety strap 安全帶
drool bushing 防漏膠套筒
insert mismatch 鑲件夾口
EDM visible 明顯火花紋
lifter scrapes 斜頂拖花
short shots 走水不齊
wall stock 料位厚薄
knit lines 走水紋
stress marks 夾水紋
uneven fill pattern 走水不平行
drag marks 拖花
sprue pretrusion 唧嘴突出高度
sprue orifice and radil size 唧嘴R尺寸
sprue bushing-keyed 唧嘴有管釘
English Chinese
program name 產口名稱
part name 零件名稱
tool name 模具名稱
tool source 模具
tool steel 模具鋼材
resin 塑 料
program number 產品編號
part number 零件編號
tool number 模具編號
customer 客戶名稱
No of cavities 內模編號
machine size 啤機噸數
drum miller 鼓形銑床
duplex horizontal miller 復式臥銑床
face miller 端面銑床
grinding miller 研磨機
plain miller 平面銑床
planer-type miller 刨式銑床
rack miller 齒條銑床
slab miller 大型平面銑床
slot miller 鍵槽銑刀
spline miller 花鍵銑刀
thread miller 螺紋銑刀
vertical miller 立式銑刀,立輥,立輥軋機
endmill 立銑刀
plastic mould steel 塑料模鋼
cold work steel 冷作鋼
hot work steel 熱作鋼
high speed steel 高速鋼
electric magnetic clutch 電磁離合器
pad printer 移印機
screen printer 絲印機
hot stamper 燙印機
solid carbide slitting saw 鉆石鋼鋸片
convex cutter 凸鑼刀片
concave cutter 凹鑼刀片
side&face cutters,staggered teeth 正側雙用鑲鉆石鋼鑼刀
end-mill 鑼刀
semi-rod 半圓刀
split double end 雙頭刀
single end 單頭刀
2-flute 兩板
3-flute 三板
4-flute 四板
reamer 直拈
centre drill 中心鉆
solid carbide drill 鉆咀
zinc ingot 鋅錠
aluminium ignot 鋁錠
tin ignot 錫錠
heater cement 發熱管得結合劑
heater groove 發熱管槽
spacer rail 介子座
cross pin 十字頭銷
nozzle plate 射嘴板
nozzle seat 熱嘴
addendum 齒冠
dedendum 齒根
air compressor 空氣壓縮機
air exhauster 抽氣機
air intake 進氣口
air seal 空氣隔離層